Mounted Seeders

For precision farming

An extensive range to meet the expectations of the most demanding farmer.

High performance machines due to their load capacity, working widths and electronic control systems.

Specifically designed to work with medium-power tractors so that sowing tasks are carried out with high precision and in the shortest possible time.

Very robust but lightweight seeders, easy to manoeuvre to make sowing a rewarding task.

Designed so that the sowing tubes adapt to the ground, both lengthwise and crosswise, in order to achieve a uniform depth of sowing throughout the field.

The seed depth is adjusted quickly and easily by means of central control and in each lateral extension.

Here you can learn more about our range for conventional tillage, minimum tillage and direct seeding.

PNEUMATIC DISTRIBUTION

The volumetric distributor is exclusively designed by AGUIRRE. Flow proportional to the forward movement in order to always maintain the desired dose.

The dosing/regulation systems allow us to sow, with absolute precision, from 1 to 300 kg/ha of any type of seed (rape, alfalfa, cereals, beans, etc.).

Adjustment of the dose is carried out via a specific window for this purpose and with the help of the flow rate table in the manual supplied with each machine.

Another emptying window allows us to change seed quickly without leaving any residue inside the hopper.

Impulsión de aire sembradoras suspendidas Aguirre

AIR DRIVE

A turbine drives the air current needed to carry the flow of seeds from the outlet of the distributor to the sowing lines distributed on the seeder body.

A dispensing head, with as many outputs as there are lines located at the top of the hopper, takes care of evenly distributing the air flow and the seeds to the entire width of the machine.

Due to its power it is possible to work with power take off regimes which are not too high in order to save fuel and so that tractor driving is quiet.

A multiplication system transforms this PTO regime to the turbine revolutions needed for the different working widths.

ELECTRONICS

Four levels of equipment to control the various functions of the seeder.

Basic console: forward speed, hectare-count, hopper level, distributor operating control, turbine control and general sowing cut-off.

Complete console: forward speed, hectare-count, hopper level, distributor operating control, turbine control, general sowing cut-off and partial cut-offs of the working width.

Heeling console: forward speed, hectare-count, hopper level, distributor operating control, turbine control and symmetrical and asymmetrical tramlining.

Electro drive: forward speed, hectare-count, hopper level, distributor operating control, turbine control, heeling and modulation of seeding rate.

RANGE

MOUNTED GRID “RS” SEEDER: (approximate measurements)

TABLA SEMBRADORA “RS” REJA SUSPENDIDA: (medidas aproximadas)

RS Grid Attachmen

The grid arm allows us to sow under extreme conditions of unprepared, wet, stony or clay soils.

Non stop device using springs to prevent breakage and which allows perfect adaptation to uneven surfaces.

Excellent depth control for sowing the most challenging seeds (rape, alfalfa, etc.) with a device that eliminates air pressure and with an anti-mud system.

For sowing in minimum and conventional tillage.

MOUNTED BOOT “BS” SEEDER: (approximate measurements)

TABLA SEMBRADORA “BS” BOTA SUSPENDIDA: (medidas aproximadas)

BS Boot Attachment

The boot arm attachment is preceded by a two row preparer which levels off the ground and removes the weeds.

The boot arm follows the land and has individual pressure control to regulate the sowing depth.

High-capacity, anti-wear boot made from cast material.

For sowing in minimum and conventional tillage.

DS DISC SERIES

DS Disc Attachment

A preparer with two rows of arms which leaves the ground ready for the double disc arm to perform a perfect sowing.

As an option we can fit a rear control wheel

Mounted Pneumatic Seeders

MOUNTED DISC “DS-R” SEEDER: (approximate measurements)

TABLA SEMBRADORA “DS-R” DISCO SUSPENDIDA: (medidas aproximadas)

TD direct Sowing attachment

The DS-R disc arm allows us to sow under extreme conditions of unprepared, stony soils with abundant plant debris on the surface.

Non stop device using springs to prevent breakage and which allows perfect adaptation to uneven surfaces.

Concentric double disc with very little opening angle in order to move just enough to deposit the seed.

For sowing in minimum and conventional tillage.

MOUNTED MULTIFUNCTIONAL GRID “TD” SEEDER: (approximate measurements)

TABLA SEMBRADORA “TD” REJA POLIVALENTE SUSPENDIDA: (medidas aproximadas)

TD direct Sowing attachment

The sowing attachment for our TD allows us to sow in any land or preparation conditions.

It includes the non stop device using springs to prevent breakage and which allows perfect adaptation to uneven surfaces.

A 160 kg pressure element allows us to sow under extreme conditions of compaction of the surface of the field.

High strength, anti-wear, steel arm with tip protected by two tungsten carbide plates. Minimum section which cuts a furrow just large enough to deposit the seed, preventing moisture loss and facilitating the covering over.

The seed is deposited in the bottom of the furrow at the desired depth, based on the type of seed, and guarantees a uniform and rapid germination.

For sowing in minimum, conventional and direct tillage.

TD Mounted Seeder

Mounted Seeder Instruction Manual